The AQUA DETECT-2 is the ideal alarm panel if it is necessary to indicate the location of the leak. The read-out display indicates the location of the leak. This module can be used with all TraceTek leak detection cables or leak detection probes. Two different circuits can be connected to the panel, with a maximum cable length of 150 metres or 10 leak detection probes. The AQUA DETECT-2 can be integrated seamlessly with any BMS system by reading the inside relay contacts.

Ideal alarm panel when indication of the leak location is not required. Alarm panel designed to monitor a single area of TraceTek sensing cable, or a small number of probes. Typical applications include monitoring for leaks around individual air conditioning or air-handling units, water-cooled machinery, tanks, pumps, sumps, lift pits, generators or other locations. Both audible and visual alarms. Visual & Audible, leak and cable break alarms. Mains failure LED indicator.

Alarm panel with touchscreen and build-in webserver. This module is sending out alarms on leak detection automatically by mail, SNMP trap and in Modbus. Very precise leak location. Details of every alarm are logged with time stamp. Different versions available for 1 to 4 separate leak detection circuits. Compatible with all NVent Raychem Tracetek leak detection cables and sensors.

This TTDM128 master panel simultaneously monitors up to 128 SIM controllers (slave units) and is networked with the BMS in Modbus RTU. Once this master panel is installed you can extend the leak detection system continuously by adding system interface modules SIM that can be installed all over the building. Product reference supplier: P000000091

The TraceTek Fast Fuel Sensor (TT-FFS) has been developed to alert to even the smallest leaks of hydrocarbon fuels. This sensor has a reaction time of just a few seconds for light or middle weight fuels such as gasoline, jet fuel, and diesel. The sensor will reset when the probe is removed from contact with the spill and the fuel is allowed to evaporate. The sensor may be used repeatedly without replacement until it will no longer reset. Product reference supplier: P000000992

The TraceTek Fast Fuel Sensor (TT-FFS) has been developed to alert to even the smallest leaks of hydrocarbon fuels. The probe detects hydrocarbons floating on water or collecting in a sump/tank. This  sensor has a reaction time  of just a few seconds for light or middle weight fuels such as gasoline, jet fuel, and diesel. The sensor will reset when the probe is removed from contact with the spill and the fuel is allowed to evaporate. The sensor may be used repeatedly without replacement until it will no longer reset. Product reference supplier: P000002290

Our leak detection system is a fully modular system that can be modified and enlarged at all times. A full range of accessories is available for easy and correct installation. This includes special mounting clips, branch-off pieces, end terminations and jumper cables.

Our leak detection system is a fully modular system that can be modified and enlarged at all times. A full range of accessories is available for easy and correct installation. This includes special mounting clips, branch-off pieces, end terminations and jumper cables.

Robust metal probe, for the detection of aqueous liquids. Ideally suited for systems where leak detection cables are not suitable due to a high probability of dirt or damage to the cable, for example in machine rooms or damp basements. The probes are placed in series, one after the other, and are always connected to an alarm module. The use of detection probes allows the monitoring for leaks in areas where sensing cables would be difficult to install, either because of the  harsh operating environment in which detection is required, or the impracticality of installing lengths of sensor cable in vulnerable areas.

TraceTek TT1000 sensing cables detect the presence of water at any point along their length. The cable is designed for a range of applications, including data center sub-floors and telecommunication rooms. Installed with an LDM alarm and locating module, the cable senses water intrusion, triggers an alarm, and pin-points the location. TT1000 sensing cable is supplied with factory-installed plastic connectors that plug together. This leak detection is a solid cable as to avoid the ingress of dirt. The smooth design allows for quick drying. TT1000 cable is extremely resistant to abrasion and corrosion. Product reference supplier: 805147-000

TT1100-OHP is a distributed sensor that can be attached to the bottom of suspended piping with nylon tie–wraps. It detects the presence of water at any point along its length. There is no need for a drip tray to bring water into contact with the sensor cable. TT1100–OHP is supplied with an absorptive synthetic fibre braid designed to wick water along the cable. The fibre is selected to be rapid drying so that once the leak is located and repaired, the cable will quickly dry and be ready for re-use. This cable is connected to an alarm panel that can locate the leak digitally to within 1 meter. Product reference supplier: P000000808

These polymer sensors TT-3000 were developed to detect and locate leakage of light water-soluble acids or bases. The cable is available in a varierty of lengths to provide as much coverage as needed. It is designed for a variety of applications, including floor surfaces, sub-floors, equipment locations, pipes, storage tanks and trenches. The cable is small, lightweight and flexible, allowing easy installation. The smooth design allows quick drying. Product reference supplier: 048179-000

The TT-5000 cable was developed to detect hydrocarbons (fuels) and to determine the location of the leak. The sensor cable will not respond to water, only to a fuel leak. It is placed around or below tanks and on pipes. The response time depends on the type of fuel, but in the region of about ten minutes (for faster sensors, see the FFS-sensor). The sensor material is made entirely of a polymer to prevent corrosion or errors caused by dirt. Its round profile makes it easy to mount to or between any pipe. Product reference supplier: 770285-000

The TT-5000-HUV is the same cable as the TT-5000 only with extra braiding to protecd it from UV light. The cable is placed around or below tanks and on pipes. Product reference supplier: P000001299

This cable was developed for detecting solvent leaks.  The cable is placed around or below tanks and on pipes. The cable will not react on the presence of water. It needs te be connected to an alarm module. Product reference supplier: 897185-000

TraceTek TT5001-HUV sensing cable detects the presence of liquid organic solvents. The cable has extra braiding to protected it from UV light. The cable can be placed around or below tanks and on pipes. It does not react to the presence of water. Product reference supplier: P000000833

This leak detection cable was developed to detect concentraded acids. The cable is designed for demanding indoor or outdoor environments. Two of the wires are acid sensitive electrodes that are jacketed with a protective coating material that provides a water resistant. Therefore the cable will not react on water. Product reference supplier: P000000817

Robust stainless steel leak detection probe, designed for the separate detection of conductive liquids (e.g. water, glycol, ...) and non-conductive liquids (e.g. fuel, oil, ...). This probe is designed to operate on its own, without other alarm control panels: it is equipped with two switching contacts (for leaks of conductive and non-conductive liquid), each with a potential-free, normally open and normally closed contact. A green, orange or red LED on the probe lights up to indicate the type of leak. This probe is perfectly suited as an autonomous detection for technical rooms, wells or rooms with fuel tanks. We also offer customization for detection in pipes, wireless detection in wells, etc.

Set of 2 Zener diodes 2 MTL-7767+ barriers 2MTL-7764+ barriers

The CADIS Leak Sense Control is a monitoring and control system for water leak detection. Placement of this system allows you to monitor and protect your building for leaks in multiple locations. The use of wireless detection probes and wirelessly controlled taps makes this system very flexible and scalable. This system can be used standalone or in combination with in-line leak detection (Aquavision Control). The system consists of 3 types of components: A central monitoring module (A): This central module is responsible for the communication between the different components and provides the users with a web-interface to set up, manage and read out the system. When a leak is detected, this module will shut off the pipes feeding the leak ("the protected zone") and generate alarms. Wireless water leak detection probes (B): These probes detect the presence of water and communicate wirelessly with the central monitoring module. These probes are battery operated and can be easily placed. These probes can be placed in technical rooms, bathrooms or other places prone to water damage. Wirelessly controlled MBV-Saver Taps (C): These taps are installed in the water supply pipes. These taps operate on a supply voltage of 230V and communicate wirelessly with the central monitoring module. When the central monitoring module receives notification of a leak, all taps in the affected zone receive a command to close. Importantly, these taps must be installed in such a way that they can never close the fire line.

Cadis supplies several types of leak detector systems according to the principle of positive pressure with integrated pump and  automatic pressure relief. The systems can be used for  monitoring of water-polluting liquids, including flammable liquids. The leak detector can be used for monitoring one or several underground tanks or non-pressurized double-walled pipelines. Please contact us for more info.

Interface module ref SIM Can be networked to a TTDM-128 master panel or connected directly to a BMS. By placing these sub-modules, you can build a large leak detection system. These sub-modules are placed in the different rooms and areas and are connected directly to the leak detection cable. These sub-module converts the analog signal from the leak sensor into a digital signal which is sent to the master module via RS485.

Interface module ref SIM Can be networked to a TTDM-128 master panel or connected directly to a BMS. By placing these sub-modules, you can build a large leak detection system. These sub-modules are placed in the different rooms and areas and are connected directly to the leak detection cable. These sub-module converts the analog signal from the leak sensor into a digital signal which is sent to the master module via RS485.

Very simple alarm module on 24V DC voltage, wich is only used in combination with a FFS sensor, offers a simple and reliable option for liquid leak detection. It is designed for use with any TraceTek sensing cable, and can be integrated into a variety of monitoring systems. The TTC module includes three sets of relay contacts which can be used for remote annunciation and equipment control. A remote annunciation device is available. Designed for less complex situations, where a single piece of TraceTek sensing cable or a small number of probes or optical oil sensors are required. Ideally suited to monitoring for leaks around individual air-conditioning or air-handling units, water-cooled machinery, tanks, pumps, sumps, lift pits, generators or other locations. Designed to withstand more volatile conditions. Clips can be used to mount to a DIN rail.

Cadis supplies leak detector systems based  on the vacuum principle. The systems can be used for water-endangering liquids regarding approved listing, with a flash point > 55°C. An integrated vacuum pump evacuates air from the interstitial space and keeps this space in a under pressure condition. This system is applicable for double-walled bottoms, or flat base tanks. It is also applicable for double-walled pipes if no leak location is required. Please contact us of more info.